| Part Number: ALLOY-1440SC |
New Page 1
ALLOY-1440SC
PCI 100Base-FX Multimode NIC (SC),
FH Bracket
The
ALLOY-1440SC is a PCI 100Base-FX Network Adapter. It has an SC
connector, and provides a maximum 2 kilometres range over
multimode cable. The adapter is fitted with a full height
bracket, and a low profile bracket is also supplied.
The ALLOY-1440SC is a 100Base-FX
Network Adapter which supports up to 2 kilometres range over
multimode fibre optic cable. The card is installed in a PCI
bus slot, and has an SC type port connector. The card has a
half height PCB, and is fitted with a half height bracket to
suit computers of this type. A low profile bracket is also
included in case the adapter is re-deployed to a LP form
factor PC.
The ALLOY-1440LSC is a member of Alloy's 1440FX Series of
PCI bus 100Base-FX Network Adaptors, designed for modern
high reliability managed fibre networks.
These adapters are compliant to PCI 2.2 and will support PCI
buses with either 5V, 3.3V or dual voltage standard PCI,
64Bit PCI or PCI-X slots. Utilising a Via 6105M Rhine
chipset, 1440FX Series Adapters provide Advanced Management
and Power Conservation features, and enable configuration of
advanced features such as Priority Queuing to increase
multimedia transfer speeds, VLAN tagging for security, TCP/UDP
checksum offloading from the host CPU and adaptive interrupt
handling to handle heavy network loads more efficiently.
Advanced power management features include low power
consumption from the 0.22 micron designed 6105M controller.
The 1440FX series comprises both multimode, singlemode and
singlecore/singlemode WDM models offering a variety of port
connector type.
Multimode fibre optic models support a maximum range of 2
kilometres, whilst singlemode models can be purchased with
up to a maximum of 60 kilometres range. WDM models enable
transmit and receive data streams to be multiplexed over a
single fibre core. All models can support a PXE BootROM, and
individual models can be ordered with the BootROM
pre-installed, with either a low or standard profile bracket
fitted.
|
Features :
| |
SC
type port connector for multimode fibre optic cable |
| |
Maximum
cable range: 2 kilometres |
| |
Low
profile PCB, fitted with a full height bracket (low profile
bracket also supplied) |
| |
PXE
BootROM support |
| |
32-bit
PCI Bus-Master Interface |
| |
Dual
voltage 3.3V/5V PCI support, supporting PCI-32bit, 64bit and
PCI-X slots |
| |
Single
chip 100Mbps Fast Ethernet Management Controller (VIA 6105M) |
| |
IEEE
802.3u 100BASE-FX standards compliant |
| |
VIA
Rhine based CSR definition provides efficient PCI
bus-mastering |
| |
Enhanced
MAC functions for 802.3 networking |
| |
802.1
Priority Transmit with maximum of eight programmable
priority queues |
| |
802.1q
Multiple VLAN support includes VLAN long frames support
(1518+4bytes), VLAN tag auto inserting and extracting on TX
and RX side and Optional auto filtering on VLAN ID |
| |
IP
header Checksum Offload supported on IPv4 frames. Support
both of TCP and UDP protocols |
| |
Supports
Physical, Broadcast, and Multicast address filtering using
both, hashing table look-up and perfect-match mechanisms |
| |
12
sets of hardware 16 bit MIB counters |
| |
WFM
2.0 compliant |
| |
DMI
2.0 (Hardware) support |
Specifications :
| Standards
Compliance |
| |
IEEE
802.3u Fast Ethernet 100Base-FX |
| |
IEEE
802.3x Full-Duplex Flow Control |
| |
IEEE
802.1q VLANs |
| Bus
Type |
| |
PCI-Bus
Revision 2.2 |
| |
Compatible
to PCI-X Revision 1.0 |
| Bus
Access Method |
| |
Bus
Master |
| Connector
Type |
| |
SC |
| Fibre
Optic Cable Type |
| |
62.5/125,
50/125΅m multimode |
| Data
Transfer Mode/Speed |
| |
100Mbps |
| |
Full
duplex with NWay Flow Control |
| I/O
Address |
| |
Automatically
determined by PCI Bus |
| Interrupt
(IRQ) |
| |
INTA
on PCI slot pin assignment |
| Diagnostic
LEDS |
| |
LINK/ACT |
| |
FDX |
| BootROM
Size |
| |
32K,
64Kbyte EPROM/FLASHROM |
| Driver
Support |
| |
All
32-bit Windows Operating Systems |
| |
AMD64,
FREEBSD, LANSVR40.DOS, LANTASTI, LINUX, MSLANMAN.DO |
| |
NETWARE,
PCNFS, PKTDRVR, SCO5, SOLARIS, UNIXWARE |
| Environmental
Specifications |
| Operating
Temperature |
| |
0°
to 55°C (32° to 104°F) |
| Humidity |
| |
10%
to 90% |
| Physical
Specifications |
| PCB
Dimensions |
| |
120mm(L)
x 56.5mm(H) |
| Weight |
| |
60
grams |
| Emission
Approvals |
| |
Complies
with C-Tick, FCC Part 15 Class A, CE |
|
| Warranty Details
|
Warranty Period :
3
Years
|
|
|
Award One Technology
Pty Ltd
